Roof flashing might be one of the least talked-about parts of a roof, but it is one of the most important. Flashing is the metal sheeting installed at every point where your roof surface meets another surface, changes direction, or is penetrated by a structure. Without it, every one of those junctions becomes a potential leak point.
On Australian homes, particularly in Queensland where heavy rainfall is common, flashing is a critical line of defence. Getting it right during installation, and maintaining it over time, is essential to keeping water out of your roof structure and your home. This guide explains the main types of flashing used on residential roofs, what each one does, and where you will find them.
What Is Roof Flashing and Why Does It Matter?
Roof flashing is formed metal sheet, typically Zincalume or Colorbond steel in Australian applications, that is shaped and installed to create a waterproof junction at points where the roof covering cannot provide a complete seal on its own. Wherever a roof surface meets a wall, a chimney, a skylight, a plumbing vent, or changes pitch, flashing is what keeps water from finding its way through the gap.
The failure of any single piece of flashing can allow water to enter the roof cavity, where it can travel significantly before appearing as a visible stain on the ceiling. This is why understanding what flashing is present on your roof, and whether it is in good condition, is a useful part of roof maintenance.
What Are the Main Types of Flashing Found on Australian Roofs?
What Is Valley Flashing?
Valley flashing lines the internal angle where two roof slopes meet. It forms a waterproof channel that directs rainfall from both roof surfaces down toward the gutters. Valley flashing carries a high volume of water during heavy rain and is one of the most critical flashings on any roof with a hip or gable configuration.
In Queensland, valley flashings need to be correctly lapped and sealed because of the intensity of local rainfall events. A valley that backs up or leaks can cause significant water damage in a short period during a storm.
What Is Step Flashing?
Step flashing is used where a sloping roof surface meets a vertical wall, such as where a roof runs alongside a second storey wall or where a lean-to roof abuts a main structure. It consists of individual pieces of flashing, each bent into an L-shape, installed in steps that integrate with the courses of the roofing material as it rises up the slope.
Step flashing works with the roof to shed water: each step piece directs water away from the wall junction and onto the next piece below. It is a system designed to handle water movement across the slope rather than relying on sealant alone.
What Is Apron Flashing?
Apron flashing, also called base flashing, is a single continuous piece of flashing installed at the base of a vertical surface where it meets the roof slope. It is commonly used at the base of a chimney, the base of a dormer wall, or where a wall sits at right angles to the roof slope. Apron flashing directs water away from the base of the wall and onto the roof surface below.
Apron flashing is often used in combination with step or counter flashing at the same structure, as no single piece of flashing is sufficient to waterproof all four sides of a structure like a chimney on its own.
What Is Counter Flashing?
Counter flashing, sometimes called cap flashing or reglet flashing, is installed over the top of base or step flashing and is embedded or secured into the vertical surface, such as a masonry chimney or wall. It overlaps the base flashing below, creating a two-layer seal that prevents water from getting behind the base flashing.
Counter flashing is particularly important on chimneys and parapet walls where the junction between the masonry and the roof is a persistent challenge. When counter flashing fails or is missing, water can work its way behind the base flashing and enter the roof structure.
What Are Barge and Fascia Flashings?
Barge flashings cover the exposed edge of the roof at the gable end, protecting the edge of the roofing sheets from wind-driven rain. Fascia flashings and gutter fascias protect the timber fascia behind the gutters from water exposure. Both are functional and aesthetic components that are replaced as part of most full roof replacements.
For fascia protection, see our fascia capping services.
What Are Penetration Flashings?
Penetration flashings seal around any pipe, vent, skylight, or other structure that passes through the roof surface. On residential roofs, the most common penetrations are plumbing vent stacks and roof ventilators. Each penetration requires a correctly installed flashing to prevent water entry around the base of the penetrating structure.
Roof ventilators require correct flashing to remain watertight. See our roof ventilators Brisbane page for more information.
What Material Should Roof Flashing Be Made From in Queensland?
In Queensland, roof flashing is most commonly made from:
- Zincalume steel: a zinc-aluminium alloy coated steel that offers excellent corrosion resistance and is compatible with most roofing materials. Widely used for valley and apron flashings
- Colorbond steel: a pre-painted steel product that can be roll-formed into flashing profiles in colours to match the roof. Used where visual consistency with the roofing sheets is desired
- Lead: used in heritage applications and around chimneys. Very pliable and durable, but increasingly expensive and less commonly specified for new work
- Aluminium: lightweight and corrosion-resistant, but requires care around dissimilar metal contact
The choice of flashing material should be compatible with the roofing material to avoid galvanic corrosion. A licensed roofing contractor will specify the correct material combination for your roof.
How Often Should Roof Flashing Be Inspected?
Flashing should be inspected as part of any professional roof inspection, which we recommend every five years or after significant storm events. After a major storm in Queensland, it is worth having the flashings checked, as wind can lift flashing edges and heavy rain can test the integrity of seals and laps.
If you are due for a roof check, our metal roof repairs team provides thorough inspections across Brisbane and Southeast Queensland.
Is Flashing Replaced During a Full Roof Replacement?
Yes. When we carry out a full roof replacement at Fortified, all flashings are replaced as a standard part of the project. Retaining old flashings under new roofing sheets is not best practice and creates potential failure points at every junction. New flashings are correctly profiled to match the new roofing material and properly integrated with the new sheets.
See our roof replacement Brisbane page for a full overview of what is included in a complete replacement project.
Works Cited
Queensland Building and Construction Commission (QBCC). “Residential Roof Installation Standards.” QBCC, www.qbcc.qld.gov.au.
Standards Australia. “AS 1562.1: Design and Installation of Sheet Roof and Wall Cladding.” Standards Australia, www.standards.org.au.
Australian Building Codes Board (ABCB). “National Construction Code.” ABCB, www.abcb.gov.au.




